Why a circle skirt hem misbehaves
On a straight skirt the hem is cut along the same grain the whole way round, so it hangs the way the fabric was woven. On a circle skirt, most of the hem lies on the bias — the diagonal between warp and weft — and bias stretches. The sections that were cut on grain stay put while the bias sections relax downwards, and the hem you so carefully measured turns into a wavy edge that hangs longer in some places than others.
This is not a mistake in your cutting. It is normal on a bias-cut hem, and the fix is scheduling rather than skill: hang the skirt before you hem it, not after.
Hang it for at least 24 hours
Finish the seams, attach the waistband or casing, and hang the skirt on a hanger from the waistband. Twenty-four hours is the minimum; two days is better for a heavy or loosely woven fabric, and a week is not excessive for a full circle in something with drape like crepe, viscose or a wool blend.
Hang it somewhere it can actually hang — clamped by the waistband on a hanger, not folded over a chair back. Weight helps: some sewers pin small weights or clothes pegs along the hem while it settles.
Mark the hem from the floor, not from the waist
Once it has dropped, put the skirt on with the waistband at the height it will be worn and stand on a hard floor. Have someone measure up from the floor to where you want the hem, working around the whole circumference and marking with pins or tailor's chalk every 10–15 cm. Measuring down from the waist instead carries every drafting error and every uneven waistband straight into the hem.
Take the skirt off, lay it flat, and check the pins look level — measuring from a hem gauge held at 90 degrees to the floor line of the skirt. Then trim the excess, leaving your hem allowance intact.
Finish it three ways
Narrow double turn. Fold under 6 mm, press, fold under another 6 mm so the raw edge is enclosed, press again, then stitch close to the fold. On a full circle this is a lot of curve to ease around a small fold, so work in 20–30 cm sections, pressing each one before moving on. A pressing ham under the curve makes a real difference.
Bias facing. Cut a strip of bias binding or self-fabric on the bias, sew it to the hem right sides together, turn it to the inside and stitch in the ditch. It handles a strongly curved hem better than a turn-up and gives a clean edge on sheer or heavy fabrics, at the cost of a little extra bulk.
Rolled hem. On fine fabrics, a rolled hem on a serger or an overlock-style rolled foot gives the flattest possible finish and adds almost no weight, which is exactly what a full circle wants.
Measure the hem allowance before you cut
The number of folds decides the allowance. Two 1 cm folds need 2 cm of turn-in; a narrow double turn of 6 mm each needs 1.2 cm. Enter that total in the calculator's hem turn-in field and the hem cutting radius grows by that amount, which is what keeps the finished length where you planned it. Skipping it is one of the most common reasons a skirt finishes a couple of centimetres short.
When it still goes wrong
- The hem curls outward. The turn-in is too wide for the curve. Trim it narrower, clip the seam allowance at intervals, and press again over a ham.
- One side hangs longer. The fabric was cut off-grain, or part of the circle was cut on the fold. Hang it longer and re-mark rather than trying to trim it level while flat.
- The hem waves in and out. Usually stretched during stitching. Press, then re-stitch with a walking foot or a slightly longer stitch, holding the fabric gently rather than pulling it.
- The hem ripples after washing. Shrinkage differs between the bias and the straight grain. Pre-wash the fabric next time, and this one will settle after a second press.
Press, then look again
Press the finished hem from the inside over a ham, not flat on the ironing board — pressing a curved hem flat crushes the curve into a crease that is hard to press out. Then hang the skirt again overnight and check it in a mirror before you call it done.
If you have not cut the skirt yet, start from the calculator so the hem allowance is built into the radius rather than added afterwards, and read the formula page if you want to see where those radii come from.
Ask about your own skirt